Booting from SAN Example

Refer to Infodoc n. 70975 if you have access.

 

I report an example of booting from SAN (QLogic QLA2462, HITACHI 9980v, 4 HBA, Brocade 48k, Solaris 10 8/07) . I do not include into it the steps for booting from net (add_install_client, /etc/ethers,etc.), creating the LUN on the storage side and the output screens of the operating system installation (it starts from the boot net or boot cdrom).

 

I hope it will help.

 

——————————————————————————————————————–

 

ok probe-scsi-all

 

/pci@15d,600000/SUNW,qlc@1,1

 

QLogic QLA2462 Host Adapter Driver(SPARC): 1.11 10/03/05

 

Firmware version 4.00.12

 

Fibre Channel Link down

 

Possible causes: No cable, incorrect connection mode or data rate

 

/pci@15d,600000/SUNW,qlc@1

 

QLogic QLA2462 Host Adapter Driver(SPARC): 1.11 10/03/05

 

Firmware version 4.00.12

 

**************** Fabric Attached Devices *******************

 

Adapter portId – 10e00

 

Device PortId 10c00 DeviceId 0 WWPN 50060e801525c721

 

/pci@15c,600000/SUNW,qlc@1,1

 

QLogic QLA2462 Host Adapter Driver(SPARC): 1.11 10/03/05

 

Firmware version 4.00.12

 

Fibre Channel Link down

 

Possible causes: No cable, incorrect connection mode or data rate

 

/pci@15c,600000/SUNW,qlc@1

 

QLogic QLA2462 Host Adapter Driver(SPARC): 1.11 10/03/05

 

Firmware version 4.00.12

 

**************** Fabric Attached Devices *******************

 

Adapter portId – 10a00

 

Device PortId 10800 DeviceId 0 WWPN 50060e801525c701

 

/pci@15c,700000/pci@1/pci@1/scsi@2,1

 

/pci@15c,700000/pci@1/pci@1/scsi@2

 

Target 3

 

Unit 0 Disk HITACHI HUS15143BSUN146GPA02

 

Target 5

 

Unit 0 Processor SUN StorEdge 3120 D1180

 

Target a

 

Unit 0 Disk HITACHI HUS15143BSUN146GPA02

 

/pci@13d,600000/SUNW,qlc@1,1

 

QLogic QLA2462 Host Adapter Driver(SPARC): 1.24 11/15/06

 

Firmware version 4.00.26

 

Fibre Channel Link down

 

Possible causes: No cable, incorrect connection mode or data rate

 

/pci@13d,600000/SUNW,qlc@1

 

QLogic QLA2462 Host Adapter Driver(SPARC): 1.24 11/15/06

 

Firmware version 4.00.26

 

Adapter portID – 10e00

 

********** Fabric Attached Devices ************

 

Dev# 0 PortID 10c00 Port WWN 50060e801525c731

 

LUN 7ff DISK HITACHI OPEN-V -SUN6002

 

/pci@13c,600000/SUNW,qlc@1,1

 

QLogic QLA2462 Host Adapter Driver(SPARC): 1.11 10/03/05

 

Firmware version 4.00.12

 

Fibre Channel Link down

 

Possible causes: No cable, incorrect connection mode or data rate

 

/pci@13c,600000/SUNW,qlc@1

 

QLogic QLA2462 Host Adapter Driver(SPARC): 1.11 10/03/05

 

Firmware version 4.00.12

 

**************** Fabric Attached Devices *******************

 

Adapter portId – 10a00

 

Device PortId 10800 DeviceId 0 WWPN 50060e801525c711

 

/pci@13c,700000/pci@1/pci@1/scsi@2,1

 

/pci@13c,700000/pci@1/pci@1/scsi@2

 

Target 8

 

Unit 0 Disk HITACHI HUS15143BSUN146GPA02

 

Target 9

 

Unit 0 Disk HITACHI HUS15143BSUN146GPA02

 

 

 

ok boot cdrom (choose the disk from the list above)

 

or

 

ok boot net (choose the disk from the list above)

 

INSTALL THE SYSTEM

 

ok boot /pci@13c,600000/SUNW,qlc@1/fp@0,0/disk@w50060e801525c711,7ff:a

 

AVAILABLE DISK SELECTIONS:

 

0. c0t8d0 <SUN146G cyl 14087 alt 2 hd 24 sec 848>

 

/pci@13c,700000/pci@1/pci@1/scsi@2/sd@8,0

 

1. c0t9d0 <SUN146G cyl 14087 alt 2 hd 24 sec 848>

 

/pci@13c,700000/pci@1/pci@1/scsi@2/sd@9,0

 

2. c1t50060E801525C711d2047 <HITACHI-OPEN-V-SUN-6002 cyl 17474 alt 2 hd 15 sec 512> boot_san

 

/pci@13c,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e801525c711,7ff

 

3. c2t50060E801525C731d2047 <HITACHI-OPEN-V-SUN-6002 cyl 17474 alt 2 hd 15 sec 512> boot_san

 

/pci@13d,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e801525c731,7ff

 

4. c3t3d0 <SUN146G cyl 14087 alt 2 hd 24 sec 848>

 

/pci@15c,700000/pci@1/pci@1/scsi@2/sd@3,0

 

5. c3t10d0 <SUN146G cyl 14087 alt 2 hd 24 sec 848>

 

/pci@15c,700000/pci@1/pci@1/scsi@2/sd@a,0

 

6. c4t50060E801525C701d2047 <HITACHI-OPEN-V-SUN-6002 cyl 17474 alt 2 hd 15 sec 512> boot_san

 

/pci@15c,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e801525c701,7ff

 

7. c5t50060E801525C721d2047 <HITACHI-OPEN-V-SUN-6002 cyl 17474 alt 2 hd 15 sec 512> boot_san

 

/pci@15d,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e801525c721,7ff

 

root@test-e # luxadm probe

 

No Network Array enclosures found in /dev/es

 

Found Fibre Channel device(s):

 

Node WWN:50060e801525c711 Device Type:Disk device

 

Logical Path:/dev/rdsk/c1t50060E801525C711d2047s2

 

Node WWN:50060e801525c731 Device Type:Disk device

 

Logical Path:/dev/rdsk/c2t50060E801525C731d2047s2

 

Node WWN:50060e801525c701 Device Type:Disk device

 

Logical Path:/dev/rdsk/c4t50060E801525C701d2047s2

 

Node WWN:50060e801525c721 Device Type:Disk device

 

Logical Path:/dev/rdsk/c5t50060E801525C721d2047s2

 

root@test-e # luxadm display /dev/rdsk/c1t50060E801525C711d2047s2

 

DEVICE PROPERTIES for disk: /dev/rdsk/c1t50060E801525C711d2047s2

 

Vendor: HITACHI

 

Product ID: OPEN-V -SUN

 

Revision: 6002

 

Serial Num: 50 125C70295

 

Unformatted capacity: 65536.875 MBytes

 

Write Cache: Enabled

 

Read Cache: Enabled

 

Minimum prefetch: 0x0

 

Maximum prefetch: 0x0

 

Device Type: Disk device

 

Path(s):

 

/dev/rdsk/c1t50060E801525C711d2047s2

 

/devices/pci@13c,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e801525c711,7ff:c,raw

 

LUN path port WWN: 50060e801525c711

 

Host controller port WWN: 2100001b32013399

 

Path status: O.K.

 

/dev/rdsk/c2t50060E801525C731d2047s2

 

/devices/pci@13d,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e801525c731,7ff:c,raw

 

LUN path port WWN: 50060e801525c731

 

Host controller port WWN: 2100001b320a0c5c

 

Path status: O.K.

 

/dev/rdsk/c4t50060E801525C701d2047s2

 

/devices/pci@15c,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e801525c701,7ff:c,raw

 

LUN path port WWN: 50060e801525c701

 

Host controller port WWN: 2100001b321f388e

 

Path status: O.K.

 

/dev/rdsk/c5t50060E801525C721d2047s2

 

/devices/pci@15d,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e801525c721,7ff:c,raw

 

LUN path port WWN: 50060e801525c721

 

Host controller port WWN: 2100001b321fbe8b

 

Path status: O.K.

 

AVAILABLE DISK SELECTIONS:

 

0. c0t8d0 <SUN146G cyl 14087 alt 2 hd 24 sec 848>

 

/pci@13c,700000/pci@1/pci@1/scsi@2/sd@8,0

 

1. c0t9d0 <SUN146G cyl 14087 alt 2 hd 24 sec 848>

 

/pci@13c,700000/pci@1/pci@1/scsi@2/sd@9,0

 

2. c1t50060E801525C711d2047 <HITACHI-OPEN-V-SUN-6002 cyl 17474 alt 2 hd 15 sec 512> boot_san

 

/pci@13c,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e801525c711,7ff

 

3. c2t50060E801525C731d2047 <HITACHI-OPEN-V-SUN-6002 cyl 17474 alt 2 hd 15 sec 512> boot_san

 

/pci@13d,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e801525c731,7ff

 

4. c3t3d0 <SUN146G cyl 14087 alt 2 hd 24 sec 848>

 

/pci@15c,700000/pci@1/pci@1/scsi@2/sd@3,0

 

5. c3t10d0 <SUN146G cyl 14087 alt 2 hd 24 sec 848>

 

/pci@15c,700000/pci@1/pci@1/scsi@2/sd@a,0

 

6. c4t50060E801525C701d2047 <HITACHI-OPEN-V-SUN-6002 cyl 17474 alt 2 hd 15 sec 512> boot_san

 

/pci@15c,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e801525c701,7ff

 

7. c5t50060E801525C721d2047 <HITACHI-OPEN-V-SUN-6002 cyl 17474 alt 2 hd 15 sec 512> boot_san

 

/pci@15d,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e801525c721,7ff

 

Specify disk (enter its number): ^D

 

root@test-e # luxadm probe

 

No Network Array enclosures found in /dev/es

 

Found Fibre Channel device(s):

 

Node WWN:50060e801525c711 Device Type:Disk device

 

Logical Path:/dev/rdsk/c1t50060E801525C711d2047s2

 

Node WWN:50060e801525c731 Device Type:Disk device

 

Logical Path:/dev/rdsk/c2t50060E801525C731d2047s2

 

Node WWN:50060e801525c701 Device Type:Disk device

 

Logical Path:/dev/rdsk/c4t50060E801525C701d2047s2

 

Node WWN:50060e801525c721 Device Type:Disk device

 

Logical Path:/dev/rdsk/c5t50060E801525C721d2047s2

 

root@test-e # luxadm display /dev/rdsk/c1t50060E801525C711d2047s2

 

DEVICE PROPERTIES for disk: /dev/rdsk/c1t50060E801525C711d2047s2

 

Vendor: HITACHI

 

Product ID: OPEN-V -SUN

 

Revision: 6002

 

Serial Num: 50 125C70295

 

Unformatted capacity: 65536.875 MBytes

 

Write Cache: Enabled

 

Read Cache: Enabled

 

Minimum prefetch: 0x0

 

Maximum prefetch: 0x0

 

Device Type: Disk device

 

Path(s):

 

/dev/rdsk/c1t50060E801525C711d2047s2

 

/devices/pci@13c,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e801525c711,7ff:c,raw

 

LUN path port WWN: 50060e801525c711

 

Host controller port WWN: 2100001b32013399

 

Path status: O.K.

 

/dev/rdsk/c2t50060E801525C731d2047s2

 

/devices/pci@13d,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e801525c731,7ff:c,raw

 

LUN path port WWN: 50060e801525c731

 

Host controller port WWN: 2100001b320a0c5c

 

Path status: O.K.

 

/dev/rdsk/c4t50060E801525C701d2047s2

 

/devices/pci@15c,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e801525c701,7ff:c,raw

 

LUN path port WWN: 50060e801525c701

 

Host controller port WWN: 2100001b321f388e

 

Path status: O.K.

 

/dev/rdsk/c5t50060E801525C721d2047s2

 

/devices/pci@15d,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e801525c721,7ff:c,raw

 

LUN path port WWN: 50060e801525c721

 

Host controller port WWN: 2100001b321fbe8b

 

Path status: O.K.

 

root@test-e # prtvtoc /dev/rdsk/c1t50060E801525C711d2047s2

 

* /dev/rdsk/c1t50060E801525C711d2047s2 (volume “boot_san”) partition map

 

*

 

* Dimensions:

 

* 512 bytes/sector

 

* 512 sectors/track

 

* 15 tracks/cylinder

 

* 7680 sectors/cylinder

 

* 17476 cylinders

 

* 17474 accessible cylinders

 

*

 

* Flags:

 

* 1: unmountable

 

* 10: read-only

 

*

 

* Unallocated space:

 

* First Sector Last

 

* Sector Count Sector

 

* 73735680 60464640 134200319

 

*

 

* First Sector Last

 

* Partition Tag Flags Sector Count Sector Mount Directory

 

0 2 00 32770560 40965120 73735679 /

 

1 3 01 0 32770560 32770559

 

2 5 00 0 134200320 134200319

 

root@test-e #

 

root@test-e # stmsboot -e

 

WARNING: stmsboot operates on each supported multipath-capable controller

 

detected in a host. In your system, these controllers are

 

/devices/pci@13c,600000/SUNW,qlc@1/fp@0,0

 

/devices/pci@13c,600000/SUNW,qlc@1,1/fp@0,0

 

/devices/pci@13d,600000/SUNW,qlc@1/fp@0,0

 

/devices/pci@13d,600000/SUNW,qlc@1,1/fp@0,0

 

/devices/pci@15c,600000/SUNW,qlc@1/fp@0,0

 

/devices/pci@15c,600000/SUNW,qlc@1,1/fp@0,0

 

/devices/pci@15d,600000/SUNW,qlc@1/fp@0,0

 

/devices/pci@15d,600000/SUNW,qlc@1,1/fp@0,0

 

If you do NOT wish to operate on these controllers, please quit stmsboot

 

and re-invoke with -D

Unknown macro: { fp | mpt }

 

to specify which controllers you wish

 

to modify your multipathing configuration for.

 

Do you wish to continue? [y/n] (default: y)

 

Checking mpxio status for driver fp

 

Checking mpxio status for driver mpt

 

WARNING: This operation will require a reboot.

 

Do you want to continue ? [y/n] (default: y)

 

The changes will come into effect after rebooting the system.

 

Reboot the system now ? [y/n] (default: y)

 

May 23 13:20:17 test-e reboot: rebooted by root

 

May 23 13:20:17 test-e syslogd: going down on signal 15

 

May 23 13:20:17 /usr/lib/snmp/snmpdx: received signal 15

 

syncing file systems… done

 

rebooting…

 

Resetting…

 

ChassisSerialNumber 0807MM2042

 

Sun Fire E25K, using IOSRAM based Console

 

Copyright 2007 Sun Microsystems, Inc. All rights reserved.

 

OpenBoot 4.22.32, 49152 MB memory installed, Serial #44714368.

 

Ethernet address 0:0:be:aa:49:80, Host ID: 82aa4980.

 

Rebooting with command: boot

 

QLogic QLA2462 Host Adapter Driver(SPARC): 1.11 10/03/05

 

Firmware version 4.00.12

 

Boot device: /pci@13c,600000/SUNW,qlc@1/fp@0,0/disk@w50060e801525c711,7ff:a File and args:

 

SunOS Release 5.10 Version Generic_127111-11 64-bit

 

Copyright 1983-2008 Sun Microsystems, Inc. All rights reserved.

 

Use is subject to license terms.

 

Hostname: test-e

 

SUNW,eri0 : 100 Mbps half duplex link up

 

stmsboot: configuring devices

 

stmsboot: /etc/vfstab has been updated.

 

Dump content: kernel pages

 

Dump device: /dev/dsk/c12t60060E801525C700000125C700000295d0s1 (dedicated)

 

Savecore directory: /var/crash/test-e

 

Savecore enabled: yes

 

stmsboot: dump configuration has been updated.

 

syncing file systems… done

 

rebooting…

 

Resetting…

 

May 23 13:26:38 test-sc0 last message repeated 2 times

 

ChassisSerialNumber 0807MM2042

 

Sun Fire E25K, using IOSRAM based Console

 

Copyright 2007 Sun Microsystems, Inc. All rights reserved.

 

OpenBoot 4.22.32, 49152 MB memory installed, Serial #44714368.

 

Ethernet address 0:0:be:aa:49:80, Host ID: 82aa4980.

 

Rebooting with command: boot

 

QLogic QLA2462 Host Adapter Driver(SPARC): 1.11 10/03/05

 

Firmware version 4.00.12

 

Boot device: /pci@13c,600000/SUNW,qlc@1/fp@0,0/disk@w50060e801525c711,7ff:a File and args:

 

SunOS Release 5.10 Version Generic_127111-11 64-bit

 

Copyright 1983-2008 Sun Microsystems, Inc. All rights reserved.

 

Use is subject to license terms.

 

Hostname: test-e

 

SUNW,eri0 : 100 Mbps half duplex link up

 

test-e console login: root

 

Password:

 

Last login: Fri May 23 13:04:50 on console

 

May 23 13:35:07 test-e login: ROOT LOGIN /dev/console

 

Sun Microsystems Inc. SunOS 5.10 Generic January 2005

 

Sourcing //.profile-EIS…..

 

root@test-e # format

 

Searching for disks…done

 

AVAILABLE DISK SELECTIONS:

 

0. c12t60060E801525C700000125C700000295d0 <HITACHI-OPEN-V-SUN-6002 cyl 17474 alt 2 hd 15 sec 512> boot_san

 

/scsi_vhci/ssd@g60060e801525c700000125c700000295

 

root@test-e luxadm -e port

 

/devices/pci@13c,600000/SUNW,qlc@1/fp@0,0:devctl CONNECTED

 

/devices/pci@15c,600000/SUNW,qlc@1/fp@0,0:devctl CONNECTED

 

/devices/pci@13d,600000/SUNW,qlc@1/fp@0,0:devctl CONNECTED

 

/devices/pci@15d,600000/SUNW,qlc@1/fp@0,0:devctl CONNECTED

 

/devices/pci@13c,600000/SUNW,qlc@1,1/fp@0,0:devctl NOT CONNECTED

 

/devices/pci@13d,600000/SUNW,qlc@1,1/fp@0,0:devctl NOT CONNECTED

 

/devices/pci@15c,600000/SUNW,qlc@1,1/fp@0,0:devctl NOT CONNECTED

 

/devices/pci@15d,600000/SUNW,qlc@1,1/fp@0,0:devctl NOT CONNECTED

 

root@test-e #

 

root@test-e # luxadm probe

 

No Network Array enclosures found in /dev/es

 

Found Fibre Channel device(s):

 

Node WWN:50060e801525c711 Device Type:Disk device

 

Logical Path:/dev/rdsk/c12t60060E801525C700000125C700000295d0s2

 

root@test-e # luxadm display /dev/rdsk/c12t60060E801525C700000125C700000295d0s2

 

DEVICE PROPERTIES for disk: /dev/rdsk/c12t60060E801525C700000125C700000295d0s2

 

Vendor: HITACHI

 

Product ID: OPEN-V -SUN

 

Revision: 6002

 

Serial Num: 50 125C70295

 

Unformatted capacity: 65536.875 MBytes

 

Write Cache: Enabled

 

Read Cache: Enabled

 

Minimum prefetch: 0x0

 

Maximum prefetch: 0x0

 

Device Type: Disk device

 

Path(s):

 

/dev/rdsk/c12t60060E801525C700000125C700000295d0s2

 

/devices/scsi_vhci/ssd@g60060e801525c700000125c700000295:c,raw

 

Controller /devices/pci@13c,600000/SUNW,qlc@1/fp@0,0

 

Device Address 50060e801525c711,7ff

 

Host controller port WWN 2100001b32013399

 

Class primary

 

State ONLINE

 

Controller /devices/pci@15c,600000/SUNW,qlc@1/fp@0,0

 

Device Address 50060e801525c701,7ff

 

Host controller port WWN 2100001b321f388e

 

Class primary

 

State ONLINE

 

Controller /devices/pci@13d,600000/SUNW,qlc@1/fp@0,0

 

Device Address 50060e801525c731,7ff

 

Host controller port WWN 2100001b320a0c5c

 

Class primary

 

State ONLINE

 

Controller /devices/pci@15d,600000/SUNW,qlc@1/fp@0,0

 

Device Address 50060e801525c721,7ff

 

Host controller port WWN 2100001b321fbe8b

 

Class primary

 

State ONLINE

 

root@test-e # fcinfo hba-port

 

HBA Port WWN: 2100001b321fbe8b

 

OS Device Name: /dev/cfg/c5

 

Manufacturer: QLogic Corp.

 

Model: 375-3294-01

 

Firmware Version: 4.2.2

 

FCode/BIOS Version: BIOS: 1.4; fcode: 1.11; EFI: 1.0;

 

Type: N-port

 

State: online

 

Supported Speeds: 1Gb 2Gb 4Gb

 

Current Speed: 4Gb

 

Node WWN: 2000001b321fbe8b

 

HBA Port WWN: 2101001b323fbe8b

 

OS Device Name: /dev/cfg/c11

 

Manufacturer: QLogic Corp.

 

Model: 375-3294-01

 

Firmware Version: 4.2.2

 

FCode/BIOS Version: BIOS: 1.4; fcode: 1.11; EFI: 1.0;

 

Type: unknown

 

State: offline

 

Supported Speeds: 1Gb 2Gb 4Gb

 

Current Speed: not established

 

Node WWN: 2001001b323fbe8b

 

HBA Port WWN: 2100001b321f388e

 

OS Device Name: /dev/cfg/c4

 

Manufacturer: QLogic Corp.

 

Model: 375-3294-01

 

Firmware Version: 4.2.2

 

FCode/BIOS Version: BIOS: 1.4; fcode: 1.11; EFI: 1.0;

 

Type: N-port

 

State: online

 

Supported Speeds: 1Gb 2Gb 4Gb

 

Current Speed: 4Gb

 

Node WWN: 2000001b321f388e

 

HBA Port WWN: 2101001b323f388e

 

OS Device Name: /dev/cfg/c10

 

Manufacturer: QLogic Corp.

 

Model: 375-3294-01

 

Firmware Version: 4.2.2

 

FCode/BIOS Version: BIOS: 1.4; fcode: 1.11; EFI: 1.0;

 

Type: unknown

 

State: offline

 

Supported Speeds: 1Gb 2Gb 4Gb

 

Current Speed: not established

 

Node WWN: 2001001b323f388e

 

HBA Port WWN: 2100001b32013399

 

OS Device Name: /dev/cfg/c1

 

Manufacturer: QLogic Corp.

 

Model: 375-3294-01

 

Firmware Version: 4.2.2

 

FCode/BIOS Version: BIOS: 1.4; fcode: 1.11; EFI: 1.0;

 

Type: N-port

 

State: online

 

Supported Speeds: 1Gb 2Gb 4Gb

 

Current Speed: 4Gb

 

Node WWN: 2000001b32013399

 

HBA Port WWN: 2101001b32213399

 

OS Device Name: /dev/cfg/c7

 

Manufacturer: QLogic Corp.

 

Model: 375-3294-01

 

Firmware Version: 4.2.2

 

FCode/BIOS Version: BIOS: 1.4; fcode: 1.11; EFI: 1.0;

 

Type: unknown

 

State: offline

 

Supported Speeds: 1Gb 2Gb 4Gb

 

Current Speed: not established

 

Node WWN: 2001001b32213399

 

HBA Port WWN: 2100001b320a0c5c

 

OS Device Name: /dev/cfg/c2

 

Manufacturer: QLogic Corp.

 

Model: 375-3294-01

 

Firmware Version: 4.2.2

 

FCode/BIOS Version: BIOS: 1.24; fcode: 1.24; EFI: 1.8;

 

Type: N-port

 

State: online

 

Supported Speeds: 1Gb 2Gb 4Gb

 

Current Speed: 4Gb

 

Node WWN: 2000001b320a0c5c

 

HBA Port WWN: 2101001b322a0c5c

 

OS Device Name: /dev/cfg/c8

 

Manufacturer: QLogic Corp.

 

Model: 375-3294-01

 

Firmware Version: 4.2.2

 

FCode/BIOS Version: BIOS: 1.24; fcode: 1.24; EFI: 1.8;

 

Type: unknown

 

State: offlineroot@test-e # luxadm fcode_download -p

 

Found Path to 0 FC100/S Cards

 

Complete

 

Found Path to 8 FC100/P, ISP2200, ISP23xx Devices

 

Opening Device: /devices/pci@15d,600000/SUNW,qlc@1,1/fp@0,0:devctl

 

Detected FCode Version: QLA2462 Host Adapter Driver(SPARC): 1.11 10/03/05

 

Opening Device: /devices/pci@15d,600000/SUNW,qlc@1/fp@0,0:devctl

 

Detected FCode Version: QLA2462 Host Adapter Driver(SPARC): 1.11 10/03/05

 

Opening Device: /devices/pci@15c,600000/SUNW,qlc@1,1/fp@0,0:devctl

 

Detected FCode Version: QLA2462 Host Adapter Driver(SPARC): 1.11 10/03/05

 

Opening Device: /devices/pci@15c,600000/SUNW,qlc@1/fp@0,0:devctl

 

Detected FCode Version: QLA2462 Host Adapter Driver(SPARC): 1.11 10/03/05

 

Opening Device: /devices/pci@13d,600000/SUNW,qlc@1,1/fp@0,0:devctl

 

Detected FCode Version: QLA2462 Host Adapter Driver(SPARC): 1.24 11/15/06

 

Opening Device: /devices/pci@13d,600000/SUNW,qlc@1/fp@0,0:devctl

 

Detected FCode Version: QLA2462 Host Adapter Driver(SPARC): 1.24 11/15/06

 

Opening Device: /devices/pci@13c,600000/SUNW,qlc@1,1/fp@0,0:devctl

 

Detected FCode Version: QLA2462 Host Adapter Driver(SPARC): 1.11 10/03/05

 

Opening Device: /devices/pci@13c,600000/SUNW,qlc@1/fp@0,0:devctl

 

Detected FCode Version: QLA2462 Host Adapter Driver(SPARC): 1.11 10/03/05

 

Complete

 

Found Path to 0 JNI1560 Devices.

 

Complete

 

Found Path to 0 Emulex Devices.

 

Complete

 

Supported Speeds: 1Gb 2Gb 4Gb

 

Current Speed: not established

 

Node WWN: 2001001b322a0c5c

 

root@test-e #

 

root@test-e # cat vfatab

 

cat: cannot open vfatab

 

root@test-e # cat vfstab

 

#device device mount FS fsck mount mount

 

#to mount to fsck point type pass at boot options

 

#

 

fd – /dev/fd fd – no –

 

/proc – /proc proc – no –

 

# non-mpxio: /dev/dsk/c1t50060E801525C711d2047s1 – – swap – no –

 

/dev/dsk/c12t60060E801525C700000125C700000295d0s1 – – swap – no –

 

# non-mpxio: /dev/dsk/c1t50060E801525C711d2047s0 /dev/rdsk/c1t50060E801525C711d2047s0 / ufs 1 no –

 

/dev/dsk/c12t60060E801525C700000125C700000295d0s0 /dev/rdsk/c12t60060E801525C700000125C700000295d0s0 / ufs 1 no –

 

/devices – /devices devfs – no –

 

ctfs – /system/contract ctfs – no –

 

objfs – /system/object objfs – no –

 

swap – /tmp tmpfs – yes –

 

root@test-e # more fp.conf

 

#

 

# Copyright 2006 Sun Microsystems, Inc. All rights reserved.

 

# Use is subject to license terms.

 

#

 

# Sun Fibre Channel Port driver configuration

 

#

 

#ident “@(#)fp.conf 1.4 06/06/22 SMI”

 

#

 

name=”fp” class=”fibre-channel” port=0;

 

name=”fp” class=”fibre-channel” port=1;

 

#

 

# Automatic configuration of the fabric is turned on by default

 

# and thus allows all devices discovered in the SAN zone to be

 

# enumerated in the Solaris devinfo tree automatically.

 

#

 

# The manual_configuration_only property may be used to

 

# disable the default behavior and force the manual configuration of

 

# the devices in the SAN. Setting manual_configuration_only=1

 

# will disable the automatic configuration of devices.

 

# NOTE: Use of this property is not recommended. If used, the

 

# fabric devices accessed at boot time need to get manually configured

 

# before the next reboot. Otherwise, fabric devices that are needed at

 

# boot time may not get configured and may cause boot problems.

 

# To manually configure fabric devices, refer to cfgadm_fp(1M).

 

# manual_configuration_only=1;

 

#

 

#

 

# To generate the binding-set specific ‘compatible’ forms used to address

 

# legacy issues the ‘scsi-binding-set’ property must be defined. (do not remove)

 

#

 

scsi-binding-set=”fcp”;

 

#

 

# List of ULP modules for loading during port driver attach time

 

#

 

load-ulp-list=”1″,”fcp”;

 

#

 

# Force attach driver to support hotplug activity (do not remove the property)

 

#

 

ddi-forceattach=1;

 

#

 

# I/O multipathing feature (MPxIO) can be enabled or disabled using

 

# mpxio-disable property. Setting mpxio-disable=”no” will activate

 

# I/O multipathing; setting mpxio-disable=”yes” disables the feature.

 

#

 

# Global mpxio-disable property:

 

#

 

# To globally enable MPxIO on all fp ports set:

 

# mpxio-disable=”no”;

 

#

 

# To globally disable MPxIO on all fp ports set:

 

# mpxio-disable=”yes”;

 

#

 

# Per port mpxio-disable property:

 

#

 

# You can also enable or disable MPxIO on a per port basis.

 

# Per port settings override the global setting for the specified ports.

 

# To disable MPxIO on port 0 whose parent is /pci@8,600000/SUNW,qlc@4 set:

 

# parent=”/pci@8,600000/SUNW,qlc@4″ port=0 mpxio-disable=”yes”;

 

#

 

# NOTE: If you just want to enable or disable MPxIO on all fp ports, it is

 

# better to use stmsboot(1M) as it also updates /etc/vfstab.

 

#

 

#

 

# You can describe a list of target port WWNs and LUN numbers which will

 

# not be configured. LUN numbers will be interpreted as decimal. White

 

# spaces and ‘,’ can be used in the list of LUN numbers.

 

#

 

# pwwn-lun-blacklist=

 

# “target-port-wwn,lun-list”

 

#

 

# To prevent LUNs 1 and 2 from being configured for target

 

# port 510000f010fd92a1 and target port 510000e012079df1, set:

 

#

 

# pwwn-lun-blacklist=

 

# “510000f010fd92a1,1,2”,

 

# “510000e012079df1,1,2″;

 

mpxio-disable=”no”;

 

root@test-e #

 

root@test-e # vi /kernel/drv/scsi_vhci.conf

 

#

 

# Copyright 2004 Sun Microsystems, Inc. All rights reserved.

 

# Use is subject to license terms.

 

#

 

#pragma ident “@(#)scsi_vhci.conf 1.9 04/08/26 SMI”

 

#

 

name=”scsi_vhci” class=”root”;

 

#

 

# Load balancing global configuration: setting load-balance=”none” will cause

 

# all I/O to a given device (which supports multipath I/O) to occur via one

 

# path. Setting load-balance=”round-robin” will cause each path to the device

 

# to be used in turn.

 

#

 

load-balance=”round-robin”;

 

#

 

# Automatic failback configuration

 

# possible values are auto-failback=”enable” or auto-failback=”disable”

 

auto-failback=”enable”;

 

#

 

# For enabling MPxIO support for 3rd party symmetric device need an

 

# entry similar to following in this file. Just replace the “SUN SENA”

 

# part with the Vendor ID/Product ID for the device, exactly as reported by

 

# Inquiry cmd.

 

#

 

# device-type-scsi-options-list =

 

# “SUN SENA”, “symmetric-option”;

 

#

 

# symmetric-option = 0x1000000;